Beer Kit Instructions – How to brew beer from a kit

Two can or all malt beer kits are the pinnacle of beer kit brewing, these kits are available in a wide range of beer styles and are the best that can be experienced in home brewing before taking up extract or grain brewing.

This kit is Bardon bitter from Matchless Homebrew.

Brewing beer from a kit

The kit contains two cans of hopped malt extract, comprehensive instructions and a sachet of yeast.

Brewing Beer kits

Recommended equipment is two 30l fermentation buckets with lids and taps, your choice of sanitising solution, a kettle, thermometer, hydrometer and trial jar and campden tablets or campden powder.
The first stage of the process is to clean and sanitise the fermentation buckets.
My recommendation before doing anything further is to dechlorinate your brewing water. Using 1/2 a crushed campden tablet or the equivalent of campden powder stirred into 25L of tap water will immediately remove all chlorine and chloramines which can give your finished beer a chemical or medicine taste.
Adding the campden powder to the tap water

Adding Campden to brewing water

Take the water required to be heated from the treated water and boil it in your kettle.

Making beer from a kit

Standing the two cans in hot water for 5 minutes prior to opening will soften the contents and make them easier to work with. Make sure to use a clean can opener.

Cans of hopped malt extract

Empty the can contents into the fermenting vessel.

Pouring malt extract

Use some of the boiled treated water to rinse out all of the can contents.

Get the malt extract out of the can

Empty the dissolved contents of the cans into the fermenting vessel.
Warning the can will be very hot, use oven gloves or similar to protect your hands!
Stir to dissolve the bulk of the malt extract in the hot water added from the can.

Stir to disolve the Malt Extract

Using the tap on the bucket containing your treated water, drop your treated water into the dissolved kit contents. This will ensure thorough mixing and also aerate your wort to give the yeast the best possible start.

brewing with a beer kit

Check that the temperature of your wort is between 20 and 28 Celsius.

The right temperature for fermentation

If the temperature is correct add the yeast.

Adding yeast to a beer kit

Take a gravity reading. In this case 1.040. If you plan to return the sample to the fermenter make sure that the hydrometer and trial jar were sanitised.

Taking a hydrometer reading

22.5 Litres of Bardon bitter waiting for the yeasties to do their thing.

Yeast pitched

18 hours later at 20C and the yeast crop is beginning to form nicely

Yeast krausen appears

28 hours in and the yeast head looks like this.

Full yeast head

7 days later and fermentation is finished
This is how it looks after a week, after another 3 days, it’ll clear down considerably and be ready for kegging.

Fermentation complete

OK so it’s been 8 days, gravity is 1.012, but now it’s time to keg.
I will be using a plastic home brew keg for this how to.
The keg was cleaned with Oxyclean, then sanitised with a solution of cheap, thin, unscented bleach. Then rinsed well with cold tap water and finally swilled out with a kettle of boiling water. (Be careful)
50g of sugar (I used demerera, but use what you prefer) was weighed out.

Sugar for carbonating beer

The sugar was added to the keg.
Using a length of hose from the tap on the fermenter, the beer was run into the keg which mixed in the sugar.

Racking beer to keg

Once all the beer was in the keg a burst of gas from an S30 cylinder was added.

S30 co2 cylinder

After 5 minutes to allow the CO2 to settle, the lid was cracked to vent the air in the keg and leave a protective blanket of CO2.
This keg has a mechanical pressure relief valve, a further squirt of gas and the indicator can be seen to be OK (Green showing)

Kit beer brewing

40 Pints of Bardon bitter conditioning.

Beer conditioning

Give it a couple of weeks before checking for clarity.